Motors

This set is specially designed for new beginners and intermediate modelers. It not only carries forward the outstanding quality of ABSIMA (powered by HOBBYWING) products but simplifies the operation. FEATURES:- Water-proof and dust-proof for all weather races- Small size with built-in capacitor module- Multiple protections: Low voltage cut-off protection for Lipo or NiMH battery / Over-heat protection / Throttle signal loss protection- Easily programmed with "jumpers"SPECIFICATION:- Application: On-road/Off-road- Cont. / Burst Current - forward: 40A / 180A- Cont. / Burst Current - reverse: 20A / 90A- Input: 2-3S LiPo / 5-9 Cells NiMH- Battery "Low-Power" Cut-off: NiMH 4.5V / 2S LiPo 6.5V / 3S LiPo 9.75V- Motor Limit 2S LiPo/5-6 Cells NiMH: 540 or 550 Motor =12T or RPM <30.000 @ 7.2V- Motor Limit 3S LiPo/7-9 Cells NiMH: 540 or 550 Motor =18T or RPM <20.000 @ 7.2V- Maximum Reverse Force: 50% - Overheat Protection: 100°- Resistance: Fwd: 0.002 Ohm, Bwd: 0.004 Ohm- Built-in BEC: 2A/6V (Linear Mode BEC)- Plug System: Tamiya- Plug & Drive System: yes- On/Off Switch: yes- Dimmension (L/W/H): 46.5x34.0x28x5 mm- Weight: 70gSPECIFICATION MOTOR:- Turns: 14x2T- RPM: 26.300- Continuous Current: 160W- Operation V: 7.2V-7.4V- Motor size: 540- Shaft length: 12,3mm- Shaft diameter: 3,19mm- Motor length: 53,2mm- Motor diameter: 35,7mm- Brushess & Springs changeable: yes- Application: TruckSCOPE OF DELIVERY:- WP1040 Brushed ESC- 14T Electric Truck Motor- Manual

We proudly present our new programmable "ALL-IN-ONE" BRUSHED SPEED CONTROLLER which can be used for 1:10 RC Crawlers and also Race Cars. The basic setting for the vehicle and battery type is done via "jumpers" on the speed controller. A programming card is also available, which can be used for even more settings. HIGHLIGHTS:One ESC suitable for all vehicle types (crawler, off-road, on-road, boat)Programmable via jumper and separately available programming card (Item 2110061)2S LiPo operation recommendedMotor ready soldered - plug-n-playProgrammable features (via programming card):Initial Start Force: 5%* / 13% / 21% / 29% Low V cut-off: 3.1V* / 3.4V / OffCrawler Setup - Initial Drag Brake: 100%* / 90% / 80% / 70%Standard Setup - Max Brake Force: 50%* / 100% / 75% / 25%Max Reverse Force: 50%* / 75% / 100%Start Mode (Punch): Medium* / Strong / Soft Standard Features ESC:Waterproof and dustproof - suitable for all weather conditions (Clean and dry the ESC after each use to avoid corrosion).Specially designed for BRUSHED RC Cars and Crawlers for excellent acceleration and sensitive driving feel.Low internal resistance and excellent heat dissipation.Multiple protection functions such as low voltage cutoff for LiPo and NiMH batteries, ESC overheat protection and signal loss protection.Easy to program with pocket-sized jumper and programming card (sold separately - item 2110061)Specification ESC:Continuous/short-term load: 80A/320AResistance: 0.0014ohmSuitable motor types: Brushed standard motors Battery recommendation: 2S LiPo / 6 cells NiMHBEC 6.0V/5AMotor limit 2S LiPo/5-6 cells NiMH: ≥ 11T or <25.000RPM Measure: 41.5*35*29.5mmPlug system: T-plugWeight: 63.4gSpecification B-Spec Motor:Turns: 19TSpeed: 22.500RPMOutput power: 140WOperating voltage: 7.2-7.4VTechnical Size: 540Motor shaft: Length 12,3mm; Durchmesser: 3,18mm Motor size: Length 53,2mm; Durchmesser: 35,7mm Ball bearings: 2Weight: 165gIncludes:1:10 Brushed V2 Speed ControllerThrust B-Spec Brushed MotorAdhesive TapeManual

This set is specially designed for new beginners and intermediate modelers. It not only carries forward the outstanding quality of ABSIMA (powered by HOBBYWING) products but simplifies the operation. FEATURES:- Water-proof and dust-proof for all weather races- Small size with built-in capacitor module- Multiple protections: Low voltage cut-off protection for Lipo or NiMH battery / Over-heat protection / Throttle signal loss protection- Easily programmed with "jumpers"SPECIFICATION:- Application: On-road/Off-road- Cont. / Burst Current - forward: 40A / 180A- Cont. / Burst Current - reverse: 20A / 90A- Input: 2-3S LiPo / 5-9 Cells NiMH- Battery "Low-Power" Cut-off: NiMH 4.5V / 2S LiPo 6.5V / 3S LiPo 9.75V- Motor Limit 2S LiPo/5-6 Cells NiMH: 540 or 550 Motor =12T or RPM <30.000 @ 7.2V- Motor Limit 3S LiPo/7-9 Cells NiMH: 540 or 550 Motor =18T or RPM <20.000 @ 7.2V- Maximum Reverse Force: 50% - Overheat Protection: 100°- Resistance: Fwd: 0.002 Ohm, Bwd: 0.004 Ohm- Built-in BEC: 2A/6V (Linear Mode BEC)- Plug System: Tamiya- Plug & Drive System: yes- On/Off Switch: yes- Dimmension (L/W/H): 46.5x34.0x28x5 mm- Weight: 70gSPECIFICATION MOTOR:- Turns: 55x2T- RPM: 7.700- Continuous Current: 85W- Operation V: 7.2V-7.4V- Motor size: 540- Shaft length: 12,3mm- Shaft diameter: 3,19mm- Motor length: 53,2mm- Motor diameter: 35,7mm- Brushess & Springs changeable: yes- Application: TruckSCOPE OF DELIVERY:- WP1040 Brushed ESC- 55T Electric Truck Motor- Manual

We proudly present our new programmable "ALL-IN-ONE" BRUSHED SPEED CONTROLLER which can be used for 1:10 RC Crawlers and also Race Cars. The basic setting for the vehicle and battery type is done via "jumpers" on the speed controller. A programming card is also available, which can be used for even more settings. HIGHLIGHTS:One ESC suitable for all vehicle types (crawler, off-road, on-road, boat)Programmable via jumper and separately available programming card (Item 2110061)2S LiPo operation recommendedMotor ready soldered - plug-n-playProgrammable features (via programming card):Initial Start Force: 5%* / 13% / 21% / 29% Low V cut-off: 3.1V* / 3.4V / OffCrawler Setup - Initial Drag Brake: 100%* / 90% / 80% / 70%Standard Setup - Max Brake Force: 50%* / 100% / 75% / 25%Max Reverse Force: 50%* / 75% / 100%Start Mode (Punch): Medium* / Strong / Soft Standard Features ESC:Waterproof and dustproof - suitable for all weather conditions (Clean and dry the ESC after each use to avoid corrosion).Specially designed for BRUSHED RC Cars and Crawlers for excellent acceleration and sensitive driving feel.Low internal resistance and excellent heat dissipation.Multiple protection functions such as low voltage cutoff for LiPo and NiMH batteries, ESC overheat protection and signal loss protection.Easy to program with pocket-sized jumper and programming card (sold separately - item 2110061)Specification ESC:Continuous/short-term load: 80A/320AResistance: 0.0014ohmSuitable motor types: Brushed standard motors Battery recommendation: 2S LiPo / 6 cells NiMHBEC 6.0V/5AMotor limit 2S LiPo/5-6 cells NiMH: ≥ 11T or <25.000RPM Measure: 41.5*35*29.5mmPlug system: T-plugWeight: 63.4gSpecification B-Spec Motor:Turns: 55TSpeed: 7.700RPMOutput power: 85WOperating voltage: 7.2-7.4VTechnical Size: 540Motor shaft: Length 12,3mm; Durchmesser: 3,18mm Motor size: Length 53,2mm; Durchmesser: 35,7mm Ball bearings: 2Weight: 165gIncludes:1:10 Brushed V2 Speed ControllerThrust B-Spec Brushed MotorAdhesive TapeManual

2260 KV33.450 rpm @ 14.8 Volt4 polesOperating voltage 7.2 - 22.2VHousing length : 74 mmHousing Ø : 36.2 mmShaft length : 15.68 mmShaft diameter: 5 mm

1:10 Brushless Motor from the Absima "REVENGE CTM" competition series.This high performance motors can be operated and controlled by sensor and sensorless. Turns : 4300KVTurns / volt: 4300kVPower: 530W Power: 70AEfficiency: 93%Voltage: 1-3S Poles: 4 -Pole Sensor: Yes Adjustable timing: Yes Ø without solder lugs: 36mm ØDrive shaft : 5 mm / Module 1 Drive shaft length: 18.8 mm Length of motor body: 53.0 mm Weight: 177.5 gr Sensor cable is included.

Hochleistungs-Brushlessmotor aus der 1:8 Absima Revenge Competition SerieDer Motor kann sowohl sensorlos als auch sensorgesteuert betrieben werdenUmdrehungen / Volt: 2300 KVPower 2100 WLeistung 145 AEffizienz 88 %Volt 14.8 - 22.2 V4 PoleSensorgesteuertEinstellbares TimingDurchmesser: ohne Lötfahnen 42 mmDurchmesser: Antriebsschaft 5,0 mm / Modul 1Länge Antriebsschaft 18,3 mmLänge Motorengehäuse 69,0 mmGewicht 320 gLieferumfang: CTM 1:8 2300 KV Motor , SensorkabelEmpfohlen für 1:8 Buggys , Truggys , Onroad

15 turns32.000 rpm16A7.2 voltMotor size 540Shaft length: 8,6mmShaft diameter 3,19mmMotor length 54mmMotor diameter 35,7mm

18 turns28.000 rpm12A7.2 voltMotor size 540Shaft length: 8,6mmShaft Durchmesser: 3,19mmMotor length 54mmMotor Durchmesser: 35,7mm

21 turns25.300 rpm9A7.2 voltMotor size 540Shaft length: 8,6mmShaft Durchmesser: 3,19mmMotor length 54mmMotor Durchmesser: 35,7mm

35 turns7.2 voltMotor size 540Shaft length: 8,6mmShaft diameter 3,19mmMotor length 54mmMotor diameter 35,7mm

45 turns7.2 voltMotor size 540Shaft length: 8,6mmShaft diameter 3,19mmMotor length 54mmMotor diameter 35,7mm

14x2 turns26.300 rpm160 watt7.2 - 7.4 voltSize 540Shaft length: 12,3mmShaft Durchmesser: 3,18mmMotor length 53,2mmMotor Durchmesser: 35,7 mm

Features : 21 x 2 Turns20.000 U/min135 Watt7.2 - 7.4 VoltBaugröße 540Wellen-Länge 12,3 mm Ø 3,18 mm

Features: - 55x2 Turns- 7.700 U/min- 85 Watt- 7.2 - 7.4V- Baugröße 540- Wellen-Länge 12,3mm- Wellendurchmesser: 3,17mm- Motor Länge: 53,2mm- Motor Durchmesser: 35,7mm

Passend für alle Thrust B-Spec Motoren

35 x 2 Turns12.800 U/min 81 Watt7.2 - 7.4 VoltBaugröße 540Wellen-Länge: 12,3 mmWellen-Durchmesser: 3,18 mm Motor-Länge 53,2 mmMotor-Durchmesser: 35,7 mm2 Kugellager

45 x 2 Turns9.800 RPM 80 Watt7.2 - 7.4 VoltSize 540Shaft length: 12,3 mmShaft Durchmesser: : 3,18 mm Motor length: 53,2 mmMotor Durchmesser: : 35,7 mm2 Ball Bearings

kV (rpm/V): 2100Input voltage: 6-12 NiMH, 2-4S LiPoCont. load capacity: 85ATemp. load capacity: 180AResistance (Ohm): 0.0065No load current @8.4V: 3.30AEfficiency: 84%Dimensions: 42 x 69mmShank length: 17mmShank diameter: 5mmWeight: 270gSensor

Dynospeed SPEC 3.0 - 1/10 Sensored Competition Brushless Motor - 3.5 Turns - 9100 KVTurns: 3.5 TurnsMotor KV: 9100 KVMotor Shaft: 3.17 mmNr of Cells: 1 - 2SMax. Current (A): 130 ANo Load Current (A): 9.1 AMotor Length: 52.6 mmMotor ø: 35.8 mmSensor Ports: 2 Sensor PortsAdjustable Timing: YesCompliant with EFRA, BRCA, IFMAR, ROAR rules

Dynospeed SPEC 3.0 - 1/10 Sensored Competition Brushless Motor - 13.5 Turns - 3050 KVTurns: 13.5 TurnsMotor KV: 3050 KVMotor Shaft: 3.17 mmNr of Cells: 1 - 3SMax. Current (A): 50 ANo Load Current (A): 1.3 AMotor Length: 52.6 mmMotor ø: 35.8 mmSensor Ports: 2 Sensor PortsAdjustable Timing: YesCompliant with EFRA, BRCA, IFMAR, ROAR rules

Dynotorq 815 - 1/8 Sensored 4-Pole Competition Brushless Motor - Turns 2D - 2350 KVTurns: 2DMotor KV: 2350 KVMotor Shaft diameter: 5 mmNr of Cells: 2 - 4SMax. Current (A): 130 AMotor Length: 68 mmMotor diameter: 40.8 mm - 42.8 mmSensor Ports: 1 Sensor Port

Dynotorq 815 - 1/8 Sensored 4-Pole Competition Brushless Motor - Turns 2D - 1750 KVTurns: 2DMotor KV: 2150 KVMotor Shaft diameter: 5 mmNr of Cells: 2 - 6SMax. Current (A): 96 AMotor Length: 68 mmMotor diameter: 40.8 mm - 42.8 mmSensor Ports: 1 Sensor Port

SPECS:Length: 49mmWidth: 45mmHeight: 45mm