Voltage Regulator/BEC

Our Battery Eliminator Circuits are small devices that eliminate the need for a receiver and servo battery pack. They draw higher voltage from the motor batteries and drop it to a voltage level that is suitable for your receiver and servos. This is required in applications which draw high power for multiple servos or use more than 3S motor packs, as most ESCs with linear BECs are not designed for these applications.Length: 30mmWidth: 15mmHeight: 10mmWeight: 11gInput voltage: 5V to 25.2V (2S to 6S LiPo)Current output: 12 volts input = 7 amps* continuous, 10 amp peak;Current output: 24 volts input = 5 amps* continuous, 7 amp peak *Ratings are determined with a 5mph airflow on the BECSelectable Output: 4.8 - 9.0V via the Castle Link (sold separately)Default voltage is 5.1V

Waterproof: NOPeak current: 14AContinuous current:- 4.75-7.0V output: 9A- 7.25V-8.5V output: 8A- 8.75V-10.0V output: 7A- 10.25-12.0V output: 6AMax volts: 12SAdjustable output voltage: 4.75 to 12VLength: 43mmWidth: 14mmHeight: 8mmWeight: 21g

The UBEC uses a high-performance DC-DC switching module that draws its voltage from 2-6S LiPos. The module regulates the voltage down to a previously defined value that is required by the receiver or other electronic devices. This is extremely stable and the output current is permanently up to 10A or briefly at 15A.Because this UBEC is not only powerful, but also waterproof and dustproof, it is particularly suitable for the use in rock crawlers.Features:- Highly efficient DC-DC regulator chip for a transmission efficiency of over 90%.- An all-metal housing design helps conduct heat and reduces electromagnetic interference.- Adjustable UBEC output voltage (6.0V / 7.4V / 8.4V) applicable for servos with different voltages.- The continuous current of UBEC is up to 10A and max. 15A and can thus be used for various electrical devices (e.g. car lights, winches, windshield wipers, etc.).- Excellent waterproof and dustproof design with IP67 rating.- Multiple protection functions: overcurrent protection, output short circuit protection, overheating protection, safe and reliable.- External switch enables the UBEC to be switched on / off easily.- LED display to show the status of the UBEC.Technical Specifications:Input Voltage: 2-6S LiPoOutput Voltage: 6.0V / 7.4V / 8.4V (adjustable)Current cont./peak: 10A / 15ADimensions: 45x20x16.2mmWeight: 34g

LiPO Volt Spion für 2, 3 oder 4 S LiPO Akkus (7.4V, 11.1V oder 14.8V), unentbehrlich für jeden Li-PO Anwender* Wird einfach am Balancer-Stecker des Akkus angesteckt: JST-EHR / XHR Anschluss passend für die meisten LiPO Akkus wie z.B. von LEMONRC, REDPOWER, Graupner, Robbe, Kokam usw.* farbige Dioden zeigen die Einzelzellen-Spannung an: wenn eine Akkuzelle über 3.4V Spannung hat, leuchtet die betreffende Diode grün; unter 3.4V leuchtet eine rote Diode. Bei einer Spannung unter 3.0V erlischt die Diode* Sie erkennen somit frühzeitig, wenn eine oder mehrere Zellen in Unterspannung geraten (was gerade bei LiPOs schnell zu Defekten führen kann)* Gewicht ca. 2.4g* Maße ca. 28 x 20 x 4mm

Summt lautstark und blinkt hell* Ideal zum Einsatz im Modell (nur 12g)* Sie sehen und hören sofort wenn Sie landen sollten* Professionelles Prüfen der Einzelzellenspannungen für 2 bis 6-zellige LiPo/Liio/LiFe Akkus* Sehr gut: Einstellbare Spannungsschwelle von 2.0 - bis 4.0V pro Zelle* Wird einfach direkt am Balanceranschluss angesteckt* Großes, sehr kontraststarkes LCD-Display* Anzeige der einzelnen Zellenspannungen sowie der Gesamtspannung sowie Spannungsdifferenz