E-Maxx

- Capacity: 7600mAh- Voltage: 7.4V- Max Continuous Discharge: 25C (190A)- Max Burst Discharge: 50C (380A)- Weight: 446g- Dimensions: 150.74*46.74*28.66mm - Balance Plug: JST-XH- Discharge Plug: XT90- Charge Rate: 1-3C Recommended, 5C Max

Alternative zu Hot Racing #TD100X06Alternative zu Hot Racing #TD90X06

Inhalt: 2 StückAlternative zu Hot Racing #TD100X06

- For six cell power Aluminum Outer Diff Case is a must; Revo and T-Maxx use RVO11L06, Summit use SUM11LH- Not intended for on road operation if the differential is replaced with a spool or lockeralternative Traxxas #5379X

Replace Traxxas Big Bore EX Long Shock TRA2661, 3762, 3762A, 2662length: 105mm (4-1/8") (not compressed)Mounting point 100mm (4")diameter: 19mm (3/4")Steel Shock Shaft 3.5mmSping 1.54mm wireDual rate 13 TurnAccept optional Shock boot if need.Can be use withSLF63FS261SLF63MR268SLF63RS286

One Steel slipper pressure plateOne Aluminum slipper hubOne Metallic Friction Materials Super Duty Slipper disk.alternative Traxxas #5351

This is a Power Double Up Slipper Pressure Plate and Slipper Hub for the Revo, T Maxx Summit,Long Chassis e-max 4x4 Slash Etc. .These are part of the slipper assembly.FEATURES:CNC Aluminum construction with Hard Anodizing.Allow you to double up the slipper surface to increass power tranfer.YOU WILL RECEIVE:One slipper pressure plateOne slipper hubREQUIREMENTS:Installation onto vehicle.COMMENTS:This replace TRA5351For double up the slipper surface you will need 2 set of TRA5352X TRX15HS, or TRX15GSHard Anodizing or Hardcoat is an electrochemically produced grey layer of hard aluminum oxide on the surface of aluminum components.

This is a Graphit Slipper Clutch for the Traxxas Revo and T-Maxx.FEATURES:Up grade your stock slipper clutchesYOU WILL RECEIVE:(3) Pads

8mm ((M5 Lock Nut) Socket hex For the Revo T-Maxx Wheel7mm (M4 Lock Nut) Socket hex For 1/10 Wheel and 2wd Slipper4mm turnbuckle wrench for most 2WD Traxxas stock turnbuckle5mm turnbuckle wrench for most 4WD Traxxas stock turnbuckle

If your chassis did not come with the e-clip style suspension pins, you'll need Traxxas part #TRX4939X to complete the upper/lower arm installation.Some E-Maxx models came with a 6x13mm front outer bearing; if your stock bearings are 6x12mm then you'll need to buy 6x13mm bearings to be able to complete the installation.

Material: plastic

Material: plastic

Material: plastic

Material: plastic

Height: 139mmWidth: 84mmHex: 17mmOffset: 1/2"

Tech Notes: RPM Shock Shaft Guards fit all Traxxas 1/10th scale molded shocks as well as Traxxas Big Bore shocks but will not fit the Traxxas Jato. They fit the T-Maxx and E-Maxx but will not work with RPM T/E-Maxx A-arms due to clearance limitations on the upper arm.

Alternative zu Traxxas #5347

Alternative zu Traxxas #5347

INCLUDES:Center Skid PlateRear Skid PlateFront Skid PlateFour 3x8mm Flat Socket Head ScrewsTen 3x10mm Flat Socket Head ScrewsInstruction sheetBolts onto T-Maxx 3.3 and the E-Maxx 16.8V without modification-does not fit earlier versions.

INCLUDES:Center Skid PlateRear Skid PlateFront Skid PlateFour 3x8mm Flat Socket Head ScrewsTen 3x10mm Flat Socket Head ScrewsInstruction sheetBolts onto T-Maxx 3.3 and the E-Maxx 16.8V without modification-does not fit earlier versions.

Bolts onto T-Maxx 3.3 and the E-Maxx 16.8V without modification-does not fit earlier versions.

SPECS:Length: 1.89" (48.2mm)Diameter: 0.157" (4mm)

ALLOY REAR ADJUSTABLE SPRING DAMPER WITH ALLOY BALL TOP&BALL ENDS-1PR SET (1.3MM,1.5MM,1.7MM COIL SPRING & 4MM THICK SHAFT)alternative Traxxas #3762A